How Do Construction Loan Draws Work?
A construction loan is not paid out in one lump sum. The money is released in stages called draws. Each time a stage of work is finished, the borrower or builder submits a draw request with supporting paperwork, the work is verified (usually by an inspection), and the funds for that stage are released. The cycle repeats until the home is finished.
The basic idea
Construction lending works on a "work in place before money out" principle: funds go out after the work they pay for exists [1]. That is very different from a regular mortgage, where the full loan is paid at closing. During construction the loan balance grows a draw at a time, and you only pay interest on what has actually been released [2].
The draw cycle, step by step
Details differ from project to project, but most draws follow the same sequence:
- A stage of work is completed. Typical stages are site work, foundation, framing, mechanical rough-ins, drywall and insulation, and finishes [3].
- A draw request is submitted. The request lists what was done and how much is being asked for, usually matched line by line to the approved budget (or schedule of values) with a percent complete for each line.
- The work is verified. Funders commonly tie each draw to an on-site inspection before the money is released [4]. The inspector's job is to confirm that the work claimed is actually in place.
- Paperwork is checked. This normally includes invoices and lien waivers, and often a title update. One lender's published requirements, for example, call for a conditional lien waiver from the general contractor with each progress payment and unconditional waivers covering work already paid for [5]. Whoever releases the money is trying to avoid a mechanic's lien, a claim that someone who worked on the property can file against it if they are not paid [1].
- Funds are released. Money may go to the contractor or builder, to the borrower as reimbursement, or to subcontractors and suppliers, depending on how the loan is set up.
- The cycle repeats. A typical residential loan goes through this four to six times, although the number varies a lot [6].
An illustrative example
Say a $400,000 loan has a foundation stage priced at $60,000. The foundation is finished, an inspector agrees, and lien waivers are in. The $60,000 is released and the loan balance goes from $0 to $60,000. If the interest rate were 8 percent, the interest-only cost that month would be about $400 (60,000 x 8% / 12). When framing is finished, the next draw is released and the balance and the interest grow with it. (These figures are for illustration only.)
Why money is released this way
Until the house is built, the lender's collateral is a partly finished structure. Releasing funds in step with verified progress keeps the amount lent from running ahead of the value that exists on the lot. It also reduces the chance of unpaid-subcontractor liens and of money being spent on something other than the build [1][7].
Where draws get stuck
Draws most often stall on missing or wrong lien waivers, an inspection that is late or does not match the request, or a request that does not line up with the approved budget. Because each request is a separate decision with its own paperwork, small errors repeat across every draw [7].
Sources
- AAPL, "Understanding Draw Management": https://aaplonline.com/articles/uncategorized/understanding-draw-management/
- Rocket Mortgage, "Construction loans: how they work and how to qualify": https://www.rocketmortgage.com/learn/construction-loans
- Fortune, "Construction loans": https://fortune.com/article/construction-loans/
- The Federal Savings Bank, "How VA construction loan draws typically work": https://www.thefederalsavingsbank.com/?p=123872
- Live Oak Bank, construction loan documents: https://resources.liveoak.bank/hubfs/construction-loans/Combined-Docs.pdf
- LoanPro, "Construction Lending" glossary: https://loanpro.io/glossary/construction-lending
- Built (GetBuilt), "What to know about construction loans: a primer for lenders": https://getbuilt.com/blog/what-to-know-about-construction-loans-a-primer-for-lenders/
Key facts
- Construction loan money is released in stages (draws), not all at once at closing.
- Draws pay for work that is already in place, which is why each one is usually verified by an inspection.
- Each draw normally comes with supporting paperwork such as invoices, lien waivers, and a request tied to the approved budget.
- Interest is generally charged only on the amount that has been released so far.
- A typical residential build goes through roughly four to six draws, but the number varies widely.
What lenders look at
Whoever releases the money treats every draw as its own decision. They want proof that the work is done, that the people who did it have been paid or will be, and that the amount requested fits the approved budget. This is why inspections, lien waivers, and line-by-line draw requests are so common. Specific forms and timing differ from one lender to the next, so this is the general pattern, not a rule for every loan.
Common mistakes
- Submitting a draw request before the work is actually finished.
- Missing or incorrect lien waivers and invoices.
- Requesting funds in a category that does not match the approved budget.
- Assuming the money arrives the same day, then running out of cash to pay the next trade.
- Letting budget changes pile up without updating the budget the draws are checked against.
When this typically happens
- After each major stage of construction is completed.
- Several times over the course of the build, with the number set by the draw schedule.
- At final completion, when the last draw is released after a final inspection.
Frequently asked questions
Do I get the whole construction loan at closing?
No. Construction loans are advanced in stages as verified work is completed, rather than being paid out all at once [2].
Do I pay interest on the full loan amount during construction?
Generally no. Payments during construction are usually interest-only on the amount that has been drawn so far, not on the total approved limit [2].
Is an inspection required for every draw?
It is very common. Many funders confirm each stage with an on-site inspection before releasing money, but the exact practice depends on the loan terms [4].
What is a lien waiver and why is it part of a draw?
A lien waiver is a signed statement that a contractor, supplier, or subcontractor has been paid (or will be, for a conditional waiver) and gives up the right to file a mechanic's lien for that work. Collecting them helps keep the property free of claims [5][1].
How OwnerDraw helps
OwnerDraw ties your budget, draw requests, lien waivers, and supporting documents together so each draw package is built from the same numbers instead of being re-created by hand every time.